Ohaus Defender 3000 scales: Commands to request the weight (and to control the scale).

The Ohaus Defender 3000 series scales with T32XW and T31P indicators can send the weight via the standard RS-232 interface. There are several ways to trigger data transmission:

1. By pressing the print button¹ on the scale,
2. automatically at each stable weight,
3. continuously² at a rate that depends on the baud rate (approx. 50 values/s with standard setting 9600 bit/s; 100 values/s with 19200 bit/s)³,
4. in intervals from 1 s to 3600 s,
5. on demand via the interface with a suitable command (bidirectional communication).

In this article I’ll describe the 5th method: a device connected to the balance via the RS-232 interface (e.g. a computer, microcontroller, PLC, etc.) sends a command to the balance and it responds with the weight:

All explanations in this article refer to the current (October 2021) generation of the Ohaus Defender 3000 with the T32XW indicator with firmware 1.03 (left in photo above) and the T31P indicator with firmware 1.14 (right in photo).

Commands to request the weight and data format of the response

To send commands to the scale and to view the reply, you can use any serial terminal software (I’ll be using HTerm). No settings need to be changed on the scale: by default, data transmission by pressing the print key (1) and requesting the weight via the interface (5) is supported.

The following commands are listed in the user manual (PDF), I’ll discuss them in detail below:

SP command (Print when stable) – does not work as expected

If the scale sent the weight as soon as it stabilized after receiving SP, this command would be very interesting. However, the Defender 3000 does something completely different: it sets the Print > Stable setting to “On” and responds with “OK”:

As far as I know, this setting cannot be changed back to “Off” with any command (except the Reset command). It must be changed directly on the indicator in the Print menu.

This command is unfortunately useless for retrieving the weight. On other scales, such as the Ohaus Defender 5000, it works as expected.

P command (Print)

The P command corresponds to pressing the Print button on the scale. Therefore, the already mentioned stability setting (Print > Stable) is observed:

Print > Stable: “On”

If Print > Stable is set to “On”, the weight is only sent if it is stable (an asterisk * appears in the upper left corner of the display when the weight is stable). If the scale receives the P command when the weight is unstable, it does not respond (and the display briefly shows “–NO–“):

Print > Stable: “Off

If Print > Stable is set to “Off”, the scale always responds to P with the weight. Unstable weights are marked with a question mark (see below).

Output format of the scale when replying to the P command

The description in the manual is largely correct:

The 7 characters for the weight correspond to the 6 digits of the scale display plus the decimal point. The legend is only used for the gross, net and tare weight (deactivated by default) and is otherwise omitted.

Example 20.00 kg, stable:

Example -3.18 kg , unstable:

Example 11,87 kg, unstable, with unit (Print > Content > Unit: “On”):

Example with gross, net and tare weight as well as unit (all entries in the Print > Content menu set to “On”), stable:

Same example as above, except that the tare value was set with “1000T” via the interface:

The only difference is “PT” (pretare) instead of “T” in the last line.

IP command (Immediate Print)

The IP command can be used only with non-verified scales. After receiving the IP command, the scale sends the weight immediately, whether it is stable or not. Moreover, the response is not influenced by settings in the scale’s menu, so Print>Stable and Print>Content do not play any role.

Output format of the scale when replying to the IP command

For a stable weight, the response consists of 16 characters:

If the weight is unstable, two characters are added (space and question mark at the end):

Other commands

CP (Continuous Print)

Activates the continuous transmission of the weight (possible only with non-verified scales), see point 3 at the beginning of this article. With 0P (zero + P) this can be deactivated again. The data format is similar to those described above.

xP (Interval Print)

Transmission every x seconds (with x from 1 to 3600), send 0P to disable. The data format is the same as the P command.

Z (Zero)

For zeroing the scale, corresponds to pressing the Zero button on the indicator. The allowed range for executing the command is controlled by the Setup > Zero setting (2% or 100% of the capacity).

Use the Z command to eliminate small residual values. It is not intended as an alternative to the tare command (see below).

T (Tare)

Same as pressing the Tare button. Suitable for “zeroing” the weight of a container or weighing individual components of a recipe.

The tare function can be deactivated by sending 0T (zero + T). The scale will then show the gross weight again instead of the net weight (only possible via this command, not via a button on the indicator). 0T is probably not supported by verified scales (I haven’t tried this out yet).

xT (Pre-tare)

Sets x as a pre-tare value, where x must be specified in g. Not possible with verified scales.

Example:

PU (Print Unit)

The scale responds with the currently used unit (without blank spaces, see example under xU).

xU (Unit)

Changes the current unit, 1U=>g, 2U=>kg, 3U=>lb, 4U=>oz, 5U=>lb:oz.

Verified scales may not support all units (this depends on your local regulations).

Example switching from kg to g:

PV (Print Version)

The scale responds with the type of indicator (T32XW or “Defender 3000” for T31P), the firmware version (Sr=Software Release) and the “legal-for-trade” setting (“ON” for verified scales, “OFF” otherwise). With this command you can easily check if your scale uses the same firmware as my test unit.

Example T32XW:

Example T31P:

<ESC> R (Reset)

Resets all settings to the factory defaults. In my tests, some settings were only applied after a restart. I see no reason to use this command during normal operation (though – unlike on the Ranger 3000 and 4000 – it fortunately didn’t seem to reset anything in the CAL menu).

Example:

Summary of how to request the weight from an Ohaus Defender 3000 scale

The IP command is the simplest way to retrieve the weight (with the unit) from the Defender 3000. However, it cannot be used with verified scales.

Alternatively, the P command can be used, which is equivalent to pressing the Print button. It is influenced by the Print > Stable setting (send only stable values) and Print > Content setting (scope of transmitted data and unit).

SP is not a command to retrieve the weight, even if the description in the manual suggests this.

The format of the scale’s response differs slightly depending on the command (I don’t know why). I therefore recommended not reading a fixed position from the response string, but searching for the first number instead (which will be the weight).